Support
Have questions about the Peak? Learn more below.
Puffco Support
![The Peak Support page | Puffco (1) The Peak Support page | Puffco (1)](https://i0.wp.com/www.puffco.com/cdn/shop/files/support.png?v=1613666049&width=2560)
Watch the video to learn how to use your Peak
How to use the Puffco Peak?
This video will show you how to use your Puffco Peak from from beginning to end of your session.
Preventing Puffco Peak Issues
The top 6 tips for preventing Puffco Peak issues, and keeping your device running strong.
Puffco Peak Rainbow Lights? - Atomizer Check
This video shows you 4 easy steps to try and solve an atomizer connection issue on your own. More often than not, one of these simple fixes will get your Peak up and running.
How to use the Puffco Peak Travel Glass
This video will show you how to use your Puffco Peak Travel Glass.
Find out more about the product
Filter questions by selecting tags
-
How do I use my Puffco Peak?
- Make sure that your Peak is fully charged before your first use. The white light on the unit will pulse while it's charging and will automatically turn off once fully charged. The Peak should take about 2.5 hours to fully charge. Use only the micro USB charger included with your Peak to do so, using different charging bricks can potentially damage the device and will void your warranty.
- Fill the glass attachment with water, just above the air-holes. Do not allow any water in the lower section of the glass (see included instructions for details) and do not fill the glass attachment water while attached to the base.
- You can then attach the glass to the base of the Peak, aligning the inlet hole on the front of the glass with the atomizer. Then carefully pushing the front of the glass into the base, then the back.
- To lock/unlock the device, hold down the button for 3-5 seconds.
- Single click to toggle through heat settings; BLUE-GREEN-RED-WHITE
- Use loading tool to place contents on the bottom surface of the bowl.
- Place carb cap on top of atomizer.
- Double click to initiate heat-up; the device will take about 20 seconds to heat up fully. Press & hold button at any point to exit heating cycle.
- Device will vibrate and lights will flash 3 times when ready for use.
- Use a cotton swab to clean the bowl after each use.
-
How do I load my Puffco Peak?
Use the loading tool included with your Peak to transfer your product into the bowl of the atomizer. Always be sure to load the contents onto the bottom of the bowl rather than along the sidewalls of the bowl for the optimal experience. Once the atomizer has been loaded you can double click the button to engage the heating element and place the carb cap on the top of the atomizer. You can also load your product while the atomizer is warm as you would with a traditional rig.
-
How do I charge my Puffco Peak?
Simply plug the base of your device into a wall outlet via the USB charger included with your Peak. While charging, the white light will pulse and the light will automatically turn off once the device is fully charged. A depleted battery will fully charge in about 2.5 hours.
-
Can I Use Any Micro Usb Charger To Charge My Peak?
While it's okay to use a different charging cable to charge your Peak base, we never suggest using a different adapter or charging brick or using a car charger. PLEASE KEEP IN MIND THAT DOING SO CAN POTENTIALLY DAMAGE THE PRODUCT AND WILL VOID YOUR WARRANTY.
-
How Long Should My Peak Battery Last?
A fully charged Peak battery should last about 30 heating cycles before needing to be recharged. Please keep in mind that using “Sesh Mode” often will deplete battery life quicker. ALSO REMEMBER TO SHUT THE DEVICE DOWN IN BETWEEN USES IN ORDER TO PRESERVE BATTERY LIFE, THE BATTERY WILL SLOWLY DEPELETE EVEN WHEN NOT IN USE.
To check your battery life click the button 3 times. The color will indicate how much battery life remains before the device needs to be recharged: Green (100% - 60%) - Yellow (60% - 30%) - Red (30% - 0%)
-
What is Sesh Mode?
We created a Sesh Mode feature that allows you to increase heat and extend your session by 15 seconds mid cycle. This can be helpful if you’ve loaded too much material and you’re in need of a temperature boost, or just looking to share with a friend. Simply double click while in use and the heat will automatically increase and your cycle will extend. Still not enough? Double click as many times as you want to keep the session going!
-
Why Are There Different Versions Of The Peak Atomizer?
While there have been different iterations of the Peak atomizer since we’ve released the device, all functionality between the atomizers are the same. We’ve only implemented slight design changes to the casing of the atomizer over time in efforts of resolving some user error related issues such as flooding/leaking.
-
What Is The Best Way To Attach/Detach The Atomizer To The Base?
We always suggest that you attach/detach the atomizer to and from the base fully assembled, with the atomizer jacket on. The top of the Peak atomizer has notches that lock the jacket into place, making it very difficult to fully attach the atomizer without it attached.
-
Whenever I Use My Peak I Hear A Buzzing Sound, Is That Normal?
Yes, a light buzzing is completely normal when the heating element is engaged and is always more apparent and noticeable when the carb cap is removed.
-
What does the Limited Warranty cover?
Puffco provides one year of coverage for only the electronic base & battery. This covers defects in materials and workmanship for one year from the date of original retail purchase.
Puffco does not warranty glass, atomizers, normal wear and tear, or damages caused by accident or abuse. To obtain service, email support@puffco.comor go to Puffco.com/warranty
You will be required to provide proof of purchase details and the device itself when making a claim under this warranty. Do not attempt to open the Puffco Peak base. This will immediately void the warranty for your product.
-
How long is the product warranted?
The Limited Warranty Period begins on the date the product was purchased by the purchaser and lasts for one year. A claim under this warranty is only eligible if it is made within the Limited Warranty Period. Repaired, replaced, and refurbished products are covered for the remainder of their original applicable Limited Warranty Period or 30 days, whichever is longer.
-
Will the Limited Warranty always apply?
This Limited Warranty shall NOT apply:
- To any Puffco-branded Products that are resold by the Purchaser or that are purchased from unauthorized resellers or unauthorized retailers. Puffco does not authorize resellers to sell on online marketplaces such as Amazon, eBay or Walmart.com.
- Where a Product’s lack of performance is due to the Purchaser’s failure to properly maintain the Product. Purchasers should note that atomizers are replaceable parts with an expected life of 1 – 3 months, depending on usage, and they require regular cleaning to maintain functionality. Please visit Support.
- If the Product has been used with aftermarket accessories such as mouthpieces that have not been approved or endorsed by Puffco.
- If damage to the Product is cosmetic, including scratches and dents, or if lack of performance is caused by normal wear and tear or normal aging of the product. Limited Warranty does not cover the standard performance degradation of batteries.
- If Puffco determines that the Product has been improperly used, altered, or tampered with in any way. Purchaser assumes the risk or liability for loss arising from misuse, alteration of Product, or failure to follow instructions provided in user manual.
- If warranty claim is made fraudulently or by misrepresentation.
- If the serial number on the product has been deliberately altered, defaced, or removed.
-
How will Puffco make things right?
If a valid warranty claim is made during the Limited Warranty Period, Puffco will repair or replace at its sole discretion, any defective Product free of charge. Replacement products may be a refurbished or a reconditioned Product of the same model.
All Products and parts that are replaced become the property of Puffco. Puffco can only ship replacement or repaired products to the country where the original Product was purchased.
-
What should I do if I think my product is defective?
If you have a question about your product or experience a problem with it, please go to Support. You will find online support tools and information to help you with your product.
To request service under this warranty, contact Puffco at support@puffco.com or puffco.com/warranty, and a Puffco representative will provide instruction on how to proceed.
To make a claim under the Limited Warranty, you must provide the defective Product and a copy of the original receipt of purchase to Puffco for inspection. The receipt of purchase must indicate the Product purchased, price paid, date of purchase, and name of merchant.
To make a claim under the Limited Warranty, you must also obtain an Return Merchandise Authorization (RMA) number from Puffco Support before returning a product. Products returned without an RMA number are not processed and will be returned to you or destroyed. Puffco will provide a pre-paid shipping label for purchasers within the United States. International returns must be paid for by the customer.
Returns must go to the address included on the return label or provided by Puffco Support. If items are returned to any address other than the specific address provided by Puffco Support, Puffco cannot guarantee that the item will be located and processed for warranty support.
Please return only the part specifically requested by Puffco Support, not the entire device.
Postal service carriers require that all items be cleaned prior to mailing. If items are mailed to Puffco uncleaned, Puffco will, in its sole discretion, either dispose of the item or charge a $100 cleaning fee before returning the item.
-
What happens when I return my product?
Once the item arrives at the address specified by Puffco Support, it will be inspected for any possible defects. The Puffco Support Representative that coordinated the return will contact you once they receive the results of the investigation. If the item is deemed defective, it will be replaced/repaired under this warranty.
-
How Do I Clean My Peak?
In preparation of cleaning, carefully remove the glass attachment before unscrewing the atomizer. Also be sure to let the bowl cool down prior to removing the atomizer from the base.
- Clean carb cap and glass by soaking in Isopropyl Alcohol (99% preferred). Be sure to rinse with water after.
- Atomizer can be cleaned by submerging fully assembled part in Isopropyl Alcohol (99% preferred). DO NOT RINSE WITH WATER, AS WATER EXPOSURE TO CERAMIC CAN POTENTIALLY DAMAGE THE PART. Be sure to clean the gold connector pin on the base and bottom of atomizer with Iso soaked cotton swab as well.*IF YOUR BOWL CANNOT BE EASILY REMOVED, DO NOT ATTEMPT TO FORCEFULLY REMOVE. See extended cleaning instructions via Support or contact support via Warranty
- WARNING: After cleaning, allow all parts to thoroughly dry before use.
*Before removing atomizer, make sure bowl has cooled down.
*Do not get base wet – its electric – it will break.
*Thoroughly clean device every 20 uses or so. -
How Often Should I Clean My Peak?
A good rule of thumb is to thoroughly clean the Peak each time the battery fully depletes and needs to be recharged. The atomizer itself should be soaked in ISO anytime you notice excess flooding or get a rainbow light response from the device.
-
What Is The Best Cleaning Solution To Clean My Peak?
The best cleaning solution to clean your Peak and Peak atomizer is 99% Isopropyl Alcohol. The reason we suggest 99% Isopropyl Alcohol specifically is because lower percentages of Isopropyl Alcohol have water content that could potentially cause issues.
-
My Device Is Flashing Rainbow Lights, What Do I Do?
The rainbow light is an indication that there is a connection issue between the base and atomizer & does not necessarily mean that anything is broken or defective. The first tip is to remove the atomizer, clean the connection pins with a cotton swab dipped in iso and reattach the atomizer. If the atomizer has not been cleaned in some time and there is any sticky material flooding the part it may be best to soak the entire atomizer in ISO, let it fully dry and then reattach the atomizer. When you do so, be sure to screw the atomizer tightly into the base. Sometimes something as simple as a loose connection can be the reason for the issue. If issues persist, contact our support team via Puffco.com/warranty
-
I’ve Changed The Atomizer On My Peak And I’m Still Getting A Rainbow Light Error. What’s Wrong With My Peak?
If you're still getting a rainbow light reaction with the connections clean and clear & a brand new atomizer, you may want to try "back threading" (turn the atomizer counter clock wise for a half turn) to ensure the atomizer threads are properly lining up to the threads of the base. Then tighten the atomizer securely to the base. If issues do persist, contact our support team via Puffco.com/warranty
-
The Light On My Device Sometimes Flashes Red While Charging, What Do I Do?
Not to worry, this simply means that the device has overheated. Simply let the Peak cool down for a little while and normal functionality/charging will resume. If your device is overheating while on the charger you should expect the charge time to take a little over 2.5 hours.
-
When I Try To Use My Peak It Flashes 5 Times And Does Not Heat. What Do I Do?
The red flashing light is to indicate that there is a short circuit somewhere in the device. Contact support@puffco.com or Puffco.com/warranty for further assistance.
-
My Atomizer Is Heating Up But I’m Not Getting Any Vapor, What Am I Doing Wrong?
This can be due the glass not being properly attached or lined up to the base of the device. Even if you’re getting airflow, the inlet hole may be slightly offset which is why no vapor is being transferred from the atomizer through the glass attachment. Simply remove the glass and reattach the piece, carefully aligning the inlet hole with the atomizer first and then popping the rear end of the glass into place. Once in, slightly turn to the right and then back in alignment with the atomizer to ensure the silicone from the base is not blocking the air path from the atomizer.
Are you having issues or having trouble using our products? We are here to support you!
Select a product below to get more information.
New Peak
Peak Pro
Proxy
Plus